Seagate 100252820 Barracuda 7200.7 PCB Circuit Board

1. I am in need of a logic board for a Seagate Barracuda 80GB hard drive. While my main computer was down, the hard drive was sitting on the desk. Someone who hasn’t admitted it dropped it onto the floor. Whe port where the IDE cable plugs in cracked and 1 of the pins came out. The computer obviously won’t read it. If you has one that maywork, please let me know. Not sure what numbers off the board we need to compare but we can figure that out. They do not make the board seperate for sale so my only chance is finding an identical hard drive and using the board
I’m willing to buy, so I can get some very important info of the hard drive.

2. I need to find the same hard drive with these specifications to remove the plate:
Model: ST340014A
S / N: 3JX38RQX
P / N: 100275520
Config: Dyz-10
Firmware: 3.06
Date Code: 04057
Site Code: AMK
Board details:
Chip (the large chip board): 100252820
Chip (chip small plate): 100244097 SMOOTH
Can you lend a hand?
Thanks!

Buy this pcb online: 100252820

Seagate 100306336 Barracuda 7200.7 PCB Circuit Board

1. My Seagate ST3200822AS PCB board was burned causing by rather the PC or an external enclosure. The hard disk was dead, can not spinning up. But somehow i managed to power on the hard disk and it’s spinning up. When i directly connect the hard disk to the SATA connector on the motherboard, sometime the hard disk is detected when the PC boots, sometimes it does not detect it. But when I connect the hard disk to the SATA connector on the SATA card. it detected when PC boots up. When the hard disk spins up, it makes some clicking noise, about 60 seconds, it stops. Windows XP starting to load and freezes and the disk is clicking sometimes. I leave it for 1 hour, and Windows XP is still not loaded.
On the other hand, I startup windows xp from another hard disk (working one), while in windows, i connect the burned pcb hard disk, the hard disk spin up and freezes windows xp and the clicking sound sometimes happen too, 1 hour later, still freezes. I also use the Seagate Diagnostic Tool — SeaTools to run Tests on the failed hard disk, when starting the Short Test, it display an error message :
DST — FAILED – Electrical Element
So i run the Long Test, the test took more than 2 hours to run. and it detects around 90 errors on the hard disk.
I also run Partition Magic and scan the hard disk for any errors, it shows lots of Read Errors and terminated the scan process because too many of this Read Errors.
Do you have any clue what’s wrong with the burned pcb hard disk? How to repaired this hard disk? Just do a PCB swap?

2. i’m from sri lanka
i’m in need of a board for my HDD
details
HDD = 160 GB
Model = ST3160023AS
P/N = 9W2814-130
HDA P/N = 100316762
Config Level = 9SMA1
Config Code = B2P-01
Firmware = 3.20
HDD Board : 100306336 rev a
chips
LSI Logic L2c2368pl
ST 100276130
winbond w9864i6dh-6
Texas SH6950 D
if anyone can send me a board via normal post i’m really thankful

Buy this pcb online: 100306336

Seagate 100291893 Barracuda 7200.7 PCB Circuit Board

I need a PCB with the following specs:
Manufacturer : Seagate
Model Number : st380011a
Part Number : 9w2003-311
HDA Partnumber: 100278288
Config: D3Y-02
Date code 04204
site code: WU
Firmware: 3.06
Boardnumber: 100291893 REV A
Hope you can help me

Buy this pcb online: 100291893

100274360 Seagate Barracuda 7200.7 PCB Circuit Board

1. I need a new PCB for:
Seagate Barracuda 7200.7 – 200 gig
Model: ST3200822A
P/N: 9W2844-301
Firmware: 3.01
Site Code: AMK
Controller: ST
Numbers on Chip:
4490D6
100274360
100300639
FS338053
990NK
MYS 99 401

2. I am looking for a 200GB seagate IDE Harddrives that purchased in November.
I don’t care if it is used or not?
I am going to trade a new 200GB Seagate + Cash for that. I bought it yesterday and I still have the recepit. It doesn’t have the same chips compare to my Seagate that I bought on Nov.
Why I do that? Because I my old 200GB circuit board is burnt and I need to recover everything from that harddrives, I need a exactly the same model and chips.
I really need you guys help, I lost 450GB total of stuff, the other one is a WD 250GB.
the chips on the Seagate 200GB are
hynix KOREA
HY57V641620HG
0424A T-6
agere
SEAGATE
AGERE 4490D6
0407T 4785225
100274360-74
100300639-83
980 B
SH6950 D
47C3CDTA

Buy this pcb online: 100274360

You helped me out in the past and wanted to get your professional advice on the following hard drive that failed.  The hard drive spins up but makes an intermittent clicking every second.  Every once in a while it will get recognized but locks the PC up it is hooked to.  Can you tell me if a PCB and Bios switch will work, or what may need to be done?

Barracuda 7200.7 PCB

Seagate Barracuda 7200.7 80GB
Mod # ST380011A
SN – 3JV994P4
P/N – 9W2003-032
HAD – 100278288
Config – D2T-06
Firmware 3.16

Find item here: Seagate Barracuda 7200.7 PCB

Q: Necesito información sobre placa disco duro  SEAGATE Barracuda 7200.7
120Gb Mod. ST3120026AS firmware 3.18 date code 05123 site code WU

A: You can order it on: https://www.hddzone.com/st3120026as-seagate-pcb-100306336-p-1443.html

When you get this PCB, you need to move your original PCB’s BIOS to the replacement PCB. The 8pins (4 pins on each sides) with 25P05VP、25P10VP、25F512、25F1024、25F1024AN、SST25VF512、SST25VF010, etc. are the BIOS.